| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
  |
|
| Basic Configuration and Installation Resources |
« View previous topic :: View next topic » |
| Author |
Message
|
| pvemuri |
 Posted: Mon Jan 05, 2004 8:51 pm Post subject: Basic Configuration and Installation Resources |
 |
|
Voyager
Joined: 05 Jan 2004
Posts: 83
Location: CA, USA
|
Hi all,
I am newbie learning MQ Integrator using trial versions. I bought a 1 year subscription at the IBM's site and downloaded MQ Integrator Broker V 2.1. I also downloaded and installed WebSphere MQ series V 5.3, along with CSD 5.0.(installed later). But when I view the memo.ptf file in the MQ Series folder I still find that the memo.ptf file says that it is verion 1 ( CSD 1). Does this CSD1 surely donot work with Inegrator Broker V 2.1.
After a complete installation, I tried to create a "HelloWorld" Message flow by putting a Message in an XYZ.INPUT queue. But the XYZ.OUTPUT queue does'nt receive any. I completed all the formalities like: configuring the nodes, defining the input and output queues, checkingout the resources.
Is there any thing I missed out?
Thanks in advance. |
|
| Back to top |
|
 |
| kirani |
| Posted: Mon Jan 05, 2004 11:24 pm Post subject: |
|
|
Jedi Knight
Joined: 05 Sep 2001
Posts: 3779
Location: Torrance, CA, USA
|
I am assuming you have setup your broker domain correctly, like created config mgr, broker, assigned broker to the topology, etc.
Can you add a Trace node to the catch terminal of your MQInput node and print ${ExceptionList} into some file. If there is any error in your messageflow, ExceptionList will give more details about it. Do you see any error logged into Event Viewer?
_________________
Kiran
IBM Cert. Solution Designer & System Administrator - WBIMB V5
IBM Cert. Solutions Expert - WMQI
IBM Cert. Specialist - WMQI, MQSeries
IBM Cert. Developer - MQSeries
|
|
| Back to top |
|
|
| Missam |
| Posted: Thu Feb 19, 2004 8:14 pm Post subject: |
|
|
Chevalier
Joined: 16 Oct 2003
Posts: 424
|
Hi Pvemuri,
You are saying you installed CSD5 for WebSphere MQ series V 5.3 if it is you should verify it by saying the command mqver to know what level of csds installed for MQ.memo.ptf shows only CSDs applied for MQSI.
if you installed CSD5 for WMQI.Its cummulative.you should start installing from CSD1 through CSD5.
And if your message is not going to Output Queue where is it going.did u Connected the fail terminal and check whether it is following that route or still staying in your input queue.If it's going to failure terminal ,you can generate ExceptionList as kirani said and post it here. |
|
| Back to top |
|
|
| jfluitsm |
| Posted: Sun Feb 22, 2004 6:15 am Post subject: |
|
|
Disciple
Joined: 24 Feb 2002
Posts: 160
Location: The Netherlands
|
Pvemuri,
Installing earlier CSDs is not needed, the CSD is cummulative and contains all changes from previous CSDs.
_________________
Jan Fluitsma
IBM Certified Solution Designer WebSphere MQ V6
IBM Certified Solution Developer WebSphere Message Broker V6 |
|
| Back to top |
|
|
|
|
|
| |
|
Page 1 of 1 |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
