| Author |
Message
|
| GFORCE |
 Posted: Tue Oct 11, 2005 8:50 am Post subject: QMGR IP ADDRESS |
 |
|
Voyager
Joined: 16 Jun 2003
Posts: 78
Location: WISCONSIN
|
Is there any way to change the QMGR ip address on a AIX v5.3.1 QMGR
_________________
THANKS |
|
| Back to top |
|
 |
| sebastianhirt |
| Posted: Tue Oct 11, 2005 8:58 am Post subject: |
|
|
Yatiri
Joined: 07 Jun 2004
Posts: 620
Location: Germany
|
A queue manager has no IP adress.
Get one for your NIC changed, and put the CONNAME parameter on your receiving channels accordingly. |
|
| Back to top |
|
|
| jefflowrey |
| Posted: Tue Oct 11, 2005 8:59 am Post subject: |
|
|
Grand Poobah
Joined: 16 Oct 2002
Posts: 19981
|
QMGRs don't have IP addresses.
Listeners use IP addresses.
Channels use IP addresses.
_________________
I am *not* the model of the modern major general. |
|
| Back to top |
|
|
| wschutz |
| Posted: Tue Oct 11, 2005 8:59 am Post subject: |
|
|
Jedi Knight
Joined: 02 Jun 2005
Posts: 3316
Location: IBM (retired)
|
Can you give more info on your scenario? I'm not sure if you mean:
"I've changed the IP address of the host machine and what do I need to change in the qmgr itself" .... -or- "I've changed the IP adress of the host machine and what do I need to change in the other qmgrs in the network"...
and also, are you using MQ clustering and DNS servers?
_________________
-wayne |
|
| Back to top |
|
|
| GFORCE |
| Posted: Tue Oct 11, 2005 9:23 am Post subject: IP ADDRESS |
|
|
Voyager
Joined: 16 Jun 2003
Posts: 78
Location: WISCONSIN
|
Ok here is the issue, I have a QMGR with the specific ip address defined as 207.230.162.108 I want to change that ip address. Ah I see that the listner is were you define what ip address the qmgr is defined to listen to am I correct ?
_________________
THANKS |
|
| Back to top |
|
|
| jefflowrey |
| Posted: Tue Oct 11, 2005 9:34 am Post subject: |
|
|
Grand Poobah
Joined: 16 Oct 2002
Posts: 19981
|
You will need to - configure the machine to know the ip address (if not already done)
- stop the listener
- start the listener on the new ip address
- change all sender channels that point to this qmgr to use the new ip address in their conname (if your channels are using dns names, this is easy)
- change any cluster receiver channels to use the correct address in their connames
- restart any affected channels (for a cluster, simplest to restart the qmgr)
_________________
I am *not* the model of the modern major general. |
|
| Back to top |
|
|
| wschutz |
| Posted: Tue Oct 11, 2005 9:34 am Post subject: |
|
|
Jedi Knight
Joined: 02 Jun 2005
Posts: 3316
Location: IBM (retired)
|
On the listener, you USUALLY specify the TCP/IP port # to listen on (-p) and MAY specify the IP address to listen on (-i). If -i isn't specified, then all IP addresses available in the stack are listened on 
Don't forget that unless you're using a DNS, the SENDER channels and CLUSRCVR / CLUSSDR channels are going to need to change too.....
_________________
-wayne |
|
| Back to top |
|
|
| GFORCE |
| Posted: Tue Oct 11, 2005 9:44 am Post subject: IP ADDRESS |
|
|
Voyager
Joined: 16 Jun 2003
Posts: 78
Location: WISCONSIN
|
Thanks once again for all your help....
_________________
THANKS |
|
| Back to top |
|
|
|
|
