| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
| Creating bar file outside of BrokerToolKit in V6.1 |
« View previous topic :: View next topic » |
| Author |
Message
|
| jeevan |
 Posted: Sun Nov 04, 2012 2:00 pm Post subject: |
 |
|
Grand Master
Joined: 12 Nov 2005
Posts: 1432
|
by mistake make new entry instead of editing.
Last edited by jeevan on Sun Nov 04, 2012 2:54 pm; edited 1 time in total |
|
| Back to top |
|
 |
| jeevan |
| Posted: Sun Nov 04, 2012 2:51 pm Post subject: |
|
|
Grand Master
Joined: 12 Nov 2005
Posts: 1432
|
[quote="jeevan"]
| fjb_saper wrote: |
| jeevan wrote: |
ERROR: Resource X1_FLOW.msgflow cannot be added to the BAR file
because it does not contain any input nodes.
ERROR: Resource x2.msgflow cannot be added to the BAR fil
e because it does not contain any input nodes.
ERROR: Resource X3.msgflow cannot be added to the BAR file be
cause it does not contain any input nodes.
ERROR: Resource x4.msgflow cannot be added to the BAR file
because it does not contain any input nodes.
ERROR: Resource x5.msgflow cannot be added to the BAR file b
ecause it does not contain any input nodes.
ERROR: Resource x6.msgflow cannot be added to the BAR
file because it does not contain any input nodes.
when I copy that .metadata. then i adds all java, message set, and two main flows but does not add subflow. the error is as i mentioned above.
I am not sure what is causing this issue. I would appreciate your help. |
OK. Seems to me you are completely confusing the levels. You cannot add any subflow with -o unless you are at WMB level 8. You say you are at level 6.1. The subflow gets in-lined into the mainflow and you only specify the -o for the mainflow...
Can you show the command line that produced these error messages?
Also to add a subflow to a bar file at level 8, I believe it has to have the name of *.subflow, not *.msgflow....
Now if those are genuine errors at level 6.1 and you did not add the subflows to the -o command, I would seriously check if the subflows are built correctly... or referenced correctly
Have fun  |
these are the command I use
%COMMAND% -b XXXX.bar -cleanBuild -data %WS% -p %P1% %P2% %P3% %P4% %P5% %P6% %P7% %P8% %P9% %P10% %P12% -o %F1% %F2% %MS%
I used this command with and without subflow being pointed with -o.
all P1 ,p2 etc are the project of all deployable artifacts
F1 and F2 are the main flows
MS is the message set
if I compile( create bar ) with .metadata directory, it works fine.
The command completes successfully.
The bar contains the following artifacts
all java projects
two main flows
message set
when I looked at the broker.xml, i can see the entries for main flows as compiled messge flows, but I can only see properties items for for the subflows. I think this is alright.
It means it is working with toolkit workspace successfully.
But I when create a new workspace and put all artifacts as it is, it errors out for classpath, and java project
ERROR:
Processing file .classpath
Failed to add file .classpath to archive file.
/XXX_JAVA is in a project that has errors.
Please correct the errors and try again.
ERROR:
Processing file .classpath
Failed to add file .classpath to archive file.
/XXX_JAVA is in a project that has errors.
Please correct the errors and try again.
ERROR:
Processing file FLOW1.msgflow
Failed to add file F2.msgflow to archive file
FLOW2.msgflow has errors.
Please correct the errors and try again.
The ESQL level for F3.msgflow is undetermined
BIP0841E The resource F3.msgflow could not be a
dded to broker archive file .
F3.msgflow has errors.
Please correct the errors and try again.
BIP0988W Error occurred while completing mqsicreatebar command
A few more points,
There are not any exteral jar files
I am compiling in my same machine I have eclipse toolkit. I just copied the whole project without .metadata directory to A new WORKSPACE |
|
| Back to top |
|
|
| fjb_saper |
| Posted: Sun Nov 04, 2012 6:28 pm Post subject: |
|
|
Grand High Poobah
Joined: 18 Nov 2003
Posts: 20756
Location: LI,NY
|
Are all the .project and .classpath files checked into your source control?
Are you using an Ant Build?
If using and Ant build try following:
- You need to be in message broker command console
- ant -Dtoolkit.home=<toolkit install path>
<toolkit install path> would be something like c:/IBM/WMBT610
Have fun
_________________
MQ & Broker admin |
|
| Back to top |
|
|
| jeevan |
| Posted: Sun Nov 04, 2012 7:30 pm Post subject: |
|
|
Grand Master
Joined: 12 Nov 2005
Posts: 1432
|
| fjb_saper wrote: |
Are all the .project and .classpath files checked into your source control?
Are you using an Ant Build?
If using and Ant build try following:
- You need to be in message broker command console
- ant -Dtoolkit.home=<toolkit install path>
<toolkit install path> would be something like c:/IBM/WMBT610
Have fun |
Both .classpath and .project files are in in each project directory. In fact this code is directly from my tool kit without even checking in the svn. But I checked, the svn portion also has these files checked in.
Again, the code is directly from the my local machine except the .metadata directory taken out.
I am not using ant so far. that is my next stage once I get compiled, I will move into ant and eventually into build server - AnthrilPro which the company using already in other departments already.
thanks |
|
| Back to top |
|
|
| YuriiTonkov |
| Posted: Fri Oct 25, 2013 3:34 am Post subject: |
|
|
Newbie
Joined: 25 Oct 2013
Posts: 5
|
|
| Back to top |
|
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
