ASG
IBM
Zystems
Cressida
Icon
Netflexity
 
  MQSeries.net
Search  Search       Tech Exchange      Education      Certifications      Library      Info Center      SupportPacs      LinkedIn  Search  Search                                                                   FAQ  FAQ   Usergroups  Usergroups
 
Register  ::  Log in Log in to check your private messages
 
RSS Feed - WebSphere MQ Support RSS Feed - Message Broker Support

MQSeries.net Forum Index » General Discussion » DLH COMMAND

Post new topic  Reply to topic
 DLH COMMAND « View previous topic :: View next topic » 
Author Message
swann
PostPosted: Tue Jun 21, 2011 1:14 pm    Post subject: DLH COMMAND Reply with quote

Acolyte

Joined: 21 Jun 2011
Posts: 50

HI Everyone,
I had created a dead letter queue on my queue manager,and there are few messages on this DL queue,Now can any one please say the command to see the DLH for that message(i mean error for those mess to sit on deadletter queue) so that i can handle those dead letter messages.
Back to top
View user's profile Send private message
exerk
PostPosted: Tue Jun 21, 2011 1:52 pm    Post subject: Reply with quote

Jedi Council

Joined: 02 Nov 2006
Posts: 6339

The command is: read the manual - search the Info Centre for dead-letter handling; it's all in there.
_________________
It's puzzling, I don't think I've ever seen anything quite like this before...and it's hard to soar like an eagle when you're surrounded by turkeys.
Back to top
View user's profile Send private message
fjb_saper
PostPosted: Tue Jun 21, 2011 9:12 pm    Post subject: Reply with quote

Grand High Poobah

Joined: 18 Nov 2003
Posts: 20756
Location: LI,NY

I think the OP is looking for a tool to inspect the messages on the DLQ so that he can formulate a rule for them... something like MO71 perhaps?
_________________
MQ & Broker admin
Back to top
View user's profile Send private message Send e-mail
shashivarungupta
PostPosted: Tue Jun 21, 2011 10:09 pm    Post subject: Re: DLH COMMAND Reply with quote

Grand Master

Joined: 24 Feb 2009
Posts: 1343
Location: Floating in space on a round rock.

swann wrote:

I had created a dead letter queue on my queue manager,and there are few messages on this DL queue,Now can any one please say the command to see the DLH for that message(i mean error for those mess to sit on deadletter queue) so that i can handle those dead letter messages.


Something is not working in your setup for sure !!
Have you looked into those scenarios, to figure out what could be wrong, when msgs go to DLQ (sending/receiving Qmgr) ? (Treat it as :HINTS: )
Qmgr Error Logs ?
What all you have done to find out the little clue about what messages and why they are into DLQ?


_________________
*Life will beat you down, you need to decide to fight back or leave it.


Last edited by shashivarungupta on Tue Jun 21, 2011 10:17 pm; edited 1 time in total
Back to top
View user's profile Send private message Send e-mail
shashivarungupta
PostPosted: Tue Jun 21, 2011 10:13 pm    Post subject: Reply with quote

Grand Master

Joined: 24 Feb 2009
Posts: 1343
Location: Floating in space on a round rock.

Congratulations fjb_saper for completing 12k posts ! (I just noticed that)
Mind Blowing Contribution and Knowledge Sharing Skills.
Thanks from my end.
_________________
*Life will beat you down, you need to decide to fight back or leave it.
Back to top
View user's profile Send private message Send e-mail
bruce2359
PostPosted: Wed Jun 22, 2011 3:37 am    Post subject: Reply with quote

Poobah

Joined: 05 Jan 2008
Posts: 9469
Location: US: west coast, almost. Otherwise, enroute.

fjb_saper wrote:
I think the OP is looking for a tool to inspect the messages on the DLQ so that he can formulate a rule for them... something like MO71 perhaps?

amqsbcg and WMQ Explorer are two methods of inspecting the dead-letterheader.
_________________
I like deadlines. I like to wave as they pass by.
ב''ה
Lex Orandi, Lex Credendi, Lex Vivendi. As we Worship, So we Believe, So we Live.
Back to top
View user's profile Send private message
shashivarungupta
PostPosted: Wed Jun 22, 2011 3:56 am    Post subject: Reply with quote

Grand Master

Joined: 24 Feb 2009
Posts: 1343
Location: Floating in space on a round rock.

bruce2359 wrote:
fjb_saper wrote:
I think the OP is looking for a tool to inspect the messages on the DLQ so that he can formulate a rule for them... something like MO71 perhaps?

amqsbcg and WMQ Explorer are two methods of inspecting the dead-letterheader.

Ya..ya.. agree !
A welcome fish to eat !
_________________
*Life will beat you down, you need to decide to fight back or leave it.
Back to top
View user's profile Send private message Send e-mail
zpat
PostPosted: Wed Jun 22, 2011 4:47 am    Post subject: Reply with quote

Jedi Council

Joined: 19 May 2001
Posts: 5866
Location: UK

MO71 is good for this. Also good for saving them to another queue or to a file, and it can remove the DLH in the process if you want to re-process the message.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic  Reply to topic Page 1 of 1

MQSeries.net Forum Index » General Discussion » DLH COMMAND
Jump to:  



You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
Protected by Anti-Spam ACP
 
 


Theme by Dustin Baccetti
Powered by phpBB © 2001, 2002 phpBB Group

Copyright © MQSeries.net. All rights reserved.