| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
  |
|
| Changing msg set name without impacting mapping node mapping |
« View previous topic :: View next topic » |
| Author |
Message
|
| Rahul999 |
 Posted: Thu Jul 01, 2010 11:26 pm Post subject: Changing msg set name without impacting mapping node mapping |
 |
|
Centurion
Joined: 14 Mar 2007
Posts: 134
|
Hi All,
Would like to know if it is possible to change message sets name(delete the old message set and create new one) without impacting the mapping for the same.
we have already developed our mapping in the mapping node and now we have a requirement where we have to change Message set name to standardize it, but it seems that if we rename the message set(which means deleting and creating the message set again) would we lose all our mapping?
Is there any way to restore that mapping, we have thousands of fields mapped and doing it again all from the very beginning would be tedious and will take lot of time.
Let me know any suggestions?
Regards, |
|
| Back to top |
|
 |
| fatherjack |
| Posted: Sat Jul 03, 2010 2:26 pm Post subject: Re: Changing msg set name without impacting mapping node map |
|
|
Knight
Joined: 14 Apr 2010
Posts: 522
Location: Craggy Island
|
| Rahul999 wrote: |
| Would like to know if it is possible to change message sets name(delete the old message set and create new one) without impacting the mapping for the same. |
Doubt it. Once you delete your message set the mappings are gone.
| Rahul999 wrote: |
| Is there any way to restore that mapping, we have thousands of fields mapped and doing it again all from the very beginning would be tedious and will take lot of time. |
This would be useful. I think there's a supportpac that converts mappings to ESQL but don't think there's anything to do the reverse.
Personally I've found the mapping nodes to be quite unpredictable (although V6 was a lot better than V5 and maybe V7 is even better). E.g. sometimes changes to message sets would leave valid mappings still in place, other times all the mappings would disappear. Consequently I much prefer to use ESQL to do anything other than very simple mapping.
_________________
Never let the facts get in the way of a good theory. |
|
| Back to top |
|
|
| fjb_saper |
| Posted: Sat Jul 03, 2010 4:24 pm Post subject: |
|
|
Grand High Poobah
Joined: 18 Nov 2003
Posts: 20756
Location: LI,NY
|
There is an unsupported way to do that.
You would have to look at the xml of the mapping and check the top and bottom more specifically. Look at it before.
Once you have changed create a new mapping (relax just map one or 2 elements), look at the xml and infer what you need to change in the original mapping xml. Once done you can delete the new mapping ...
Have fun 
_________________
MQ & Broker admin |
|
| Back to top |
|
|
| Amitha |
| Posted: Tue Jul 06, 2010 6:37 am Post subject: |
|
|
Voyager
Joined: 20 Nov 2009
Posts: 80
Location: Newyork
|
| Quote: |
| Is there any way to restore that mapping, we have thousands of fields mapped and doing it again all from the very beginning would be tedious and will take lot of time. |
I have actually done this, in my case the message definitions were same and it was Toolkit V7.0.
Create new Message set, then in the mapping node add the new source or target message, now delete the old message(source or target) by right click remove. All the old mapping is copied automatically to the new message.
I doubt this is supported in v6.1 or 6.0. |
|
| Back to top |
|
|
|
|
|
| |
|
Page 1 of 1 |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
