| Author |
Message
|
| jhidalgo |
 Posted: Thu Oct 15, 2009 8:03 pm Post subject: Undo the RESET CLUSTER |
 |
|
Disciple
Joined: 26 Mar 2008
Posts: 161
|
How can I add again a qmgr that has been removed from the cluster with a RESET CLUSTER() QMID() ?
thanks. |
|
| Back to top |
|
 |
| Mr Butcher |
| Posted: Thu Oct 15, 2009 9:51 pm Post subject: |
|
|
Padawan
Joined: 23 May 2005
Posts: 1716
|
follow the documented procedure to add a qmgr into a cluster.
_________________
Regards, Butcher |
|
| Back to top |
|
|
| jhidalgo |
| Posted: Fri Oct 16, 2009 7:43 am Post subject: |
|
|
Disciple
Joined: 26 Mar 2008
Posts: 161
|
I have followed the procedure, and this is what always happens:
the FRs see the qmgr as being part of the cluster, channels from the FRs to the qmgr work, and channels from the qmgr to the FRs also work, BUT on the qmgr if I do "DIS CLUSQMGR(*) SUSPEND" it shows two things:
1. shows that it can't get the QMID of the FRs, it shows: (SYSTEM.TEMPQMGR.......)
2. it shows FRs with SUSPEND(YES) |
|
| Back to top |
|
|
| Vitor |
| Posted: Fri Oct 16, 2009 8:35 am Post subject: |
|
|
Grand High Poobah
Joined: 11 Nov 2005
Posts: 26093
Location: Texas, USA
|
| jhidalgo wrote: |
| 1. shows that it can't get the QMID of the FRs, it shows: (SYSTEM.TEMPQMGR.......) |
Then it's not working, probably one of the channels or (on early versions) the repro process has failed.
_________________
Honesty is the best policy.
Insanity is the best defence. |
|
| Back to top |
|
|
| Sam Uppu |
| Posted: Fri Oct 16, 2009 10:19 am Post subject: |
|
|
Yatiri
Joined: 11 Nov 2008
Posts: 610
|
This is what I see in the Clustering red book(SC34-6589-00).
Symptom — DISPLAY CLUSQMGR shows CLUSQMGR names starting SYSTEM.TEMP.
DISPLAY CLUSQMGR shows CLUSQMGR names starting SYSTEM.TEMP. 1 : display clusqmgr(*)
AMQ8441: Display Cluster Queue Manager details. CLUSQMGR(QM1) CLUSTER(DEMO) CHANNEL(TO.QM1)
AMQ8441: Display Cluster Queue Manager details.
CLUSQMGR(SYSTEM.TEMPQMGR.computer.hursley.ibm.com(1414))
CLUSTER(DEMO) CHANNEL(TO.QM2)
Cause
This queue manager has not received any information from the full repository queue manager that the manually defined CLUSSDR channel points to. The manually defined CLUSSDR should be in running state, check that the CLUSRCVR definition is also correct, especially its conname and cluster parameters. Alter the channel definition. It may take some time for the remote queue managers to complete a retry cycle and restart their channels with the corrected definition.
Thanks. |
|
| Back to top |
|
|
| fjb_saper |
| Posted: Fri Oct 16, 2009 10:31 am Post subject: |
|
|
Grand High Poobah
Joined: 18 Nov 2003
Posts: 20756
Location: LI,NY
|
per IBM docu a REFRESH CLUSTER (clustername) should do it.
You would need to run that on the qmgr you booted out of the cluster.
_________________
MQ & Broker admin |
|
| Back to top |
|
|
|
|
