| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
  |
|
| AMQ9206: Error sending data to host |
« View previous topic :: View next topic » |
| Author |
Message
|
| yoon |
 Posted: Fri Oct 27, 2006 9:57 pm Post subject: AMQ9206: Error sending data to host |
 |
|
Novice
Joined: 18 Aug 2006
Posts: 14
|
Hi i have get the following error when i have check the log in AMQERR01.LOG. It show the following info
Record the error values and tell the system administrator.
----- amqccita.c : 611 --------------------------------------------------------
10/28/2006 13:15:32
AMQ9206: Error sending data to host MyDC05966 (172.28.76.205).
EXPLANATION:
An error occurred sending data over TCP/IP to MyDC05966 (172.28.76.205). This
may be due to a communications failure.
ACTION:
The return code from the TCP/IP(send) call was 10054 X('2746'). Record these
values and tell your systems administrator.
----- amqccita.c : 2052 -------------------------------------------------------
As the same time, when i check the log in event viewer. It show the following info, may you help to solve this???
Event Type: Error
Event Source: WebSphere MQ
Event Category: None
Event ID: 9203
Date: 10/28/2006
Time: 1:48:39 PM
User: N/A
Computer: MYDC05966
Description:
A configuration error for TCP/IP occurred.
Error in configuration for communications to host ''. Allocation of a TCP/IP conversation to host '' was not possible.
The configuration error may be one of the following: &N &B 1.If the communications protocol is LU 6.2, it may be that one of the transmission parameters (Mode, or TP Name) is incorrect. Correct the error and try again. The mode name should be the same as the mode defined on host ''. The TP name on '' should be defined. &N &B 2.If the communications protocol is LU 6.2, it may be that an LU 6.2 session has not been established. Contact your systems administrator. &N &B 3.If the communications protocol is TCP/IP, it may be that the host name specified is incorrect. Correct the error and try again. &N &B 4.If the communications protocol is TCP/IP, it may be that the host name specified cannot be resolved to a network address. The host name may not be in the nameserver. &P The return code from the TCP/IP (connect) call was 10049 (X'2741'). &P Record the error values and tell the system administrator.
_________________
{-'_'-}yoon |
|
| Back to top |
|
 |
| ramires |
| Posted: Sat Oct 28, 2006 2:57 am Post subject: |
|
|
Knight
Joined: 24 Jun 2001
Posts: 523
Location: Portugal - Lisboa
|
You have to check TCP connections , ping the remote address for example.
Also check if remote listener is available.
In the case you show there are two different situations:
TCP rc 10049 and TCP rc 10054.
Regards |
|
| Back to top |
|
|
| wschutz |
| Posted: Sat Oct 28, 2006 4:05 am Post subject: |
|
|
Jedi Knight
Joined: 02 Jun 2005
Posts: 3316
Location: IBM (retired)
|
You might want to do a search here for those TCP/IP codes, you'll get quite a few hits.
_________________
-wayne |
|
| Back to top |
|
|
| yoon |
| Posted: Tue Oct 31, 2006 6:50 am Post subject: |
|
|
Novice
Joined: 18 Aug 2006
Posts: 14
|
It is working fine now but i do not know what reason. Previously i have problem when using create a default onfiguration in wizard. But when i create manually, the error no longer happen. Thank you all if have provide any opinion.
_________________
{-'_'-}yoon |
|
| Back to top |
|
|
|
|
|
| |
|
Page 1 of 1 |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
