| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
  |
|
| BIP1536S |
« View previous topic :: View next topic » |
| Author |
Message
|
| mrlazy |
 Posted: Mon May 15, 2006 1:46 pm Post subject: BIP1536S |
 |
|
Centurion
Joined: 19 Apr 2006
Posts: 144
|
When deployed a sample message flow to default execution group, I am getting the following errors:
BIP1536S, BIP2087E,BIP2062E,(though the last one is due to bad msg flow i guess. When I create a new execution group and deploy the msg flow, I get only BIP1536S.
Heres what I did:
I'm using Windows XP, MQ 5.3 FP 11, MQSI 2.1 FP 8, DB2 8.1 FP 5
Tested a msg flow initially. It worked fine. So Exported the whole topology,msg flows(test), and sets.
Backed up the CMDB and MRDB.
Restored CMDB and MRDB successfully.
Deleted Config Mgr and recreated successfully.
Imported the topology and msg flows.
Did a full deployment.
I searched mqseries and followed wat Jeff said to one other guy regarding the same problem.
| jefflowrey wrote: |
| Diagnostic Messages wrote: |
BIP1536
Severity
30 : Severe error
Message
Configuration Manager unable to register for internal subscriptions with broker <insert_0>.
Explanation
Although the preceding deploy operation was successful, a subsequent attempt by the Configuration Manager to register for internal subscriptions with broker <insert_0> was not successful. This means that the Message Brokers Toolkit may not reliably show the correct status of the resources assigned to broker <insert_0>. The Configuration Manager also writes this message to the system event log, accompanied by other messages giving details of the problem.
Response
Look at the messages for this problem in the system event log. Determine and correct the cause of the problem before attempting to deploy to this broker again. If this problem persists, contact your IBM support center. |
Look for errors on the Broker system. Look for additional errors on the configmgr system.
Confirm that the MQ traffic between the broker and the configmgr is operational.
Confirm that the security options specified to mqsicreateconfigmgr were actually correct, and confirm that the configMgr can properly connect to the security domain it needs to.
Confirm that the configmgr service user is fully authorized to all the mq resources on the broker queue managers.
Confirm that you have applied, *successfully*, at least FP3 of 5.0, if not FP4 or FP5. |
CMQM and Broker QM have connection establshed properly.
Is there sometihng else that I'm missing?Please guide me. |
|
| Back to top |
|
 |
| dilse |
| Posted: Mon May 15, 2006 2:05 pm Post subject: |
|
|
Master
Joined: 24 Jun 2004
Posts: 270
|
mrlazy
| Quote: |
| Look at the messages for this problem in the system event log. |
Did you find anything interesting in Event Viewer log? and also check this out:
http://www.mqseries.net/phpBB2/viewtopic.php?t=736&sid=b631480743db686161f7f8c23ca5a591
and here is some info thats is in the Info Center
| Quote: |
Message BIP1536
Scenario: You have defined a Configuration Manager to run with one user ID and you have defined a broker to run on a different computer with a different user ID. When you try to deploy message flows to the broker, deployment is successful but you see the error message BIP1536.
Explanation: The Configuration Manager is unable to register for internal subscriptions with the broker because the broker is running under one ID and the Configuration Manager is running under another ID. The broker and the Configuration Manager relay internal messages back and forth via publish/subscribe. These message are carried through WebSphere MQ, which requires certain authorizations.
Solution: Do the following:
Ensure that the broker's user ID is a member of the mqm and mqbrkrs groups.
Define the broker's user ID on the computer where the Configuration Manager is running.
Define the Configuration Manager's user ID on the computer where the broker is running.
Ensure that all IDs are in lowercase so that they are compatible between computers. |
|
|
| Back to top |
|
|
| mrlazy |
| Posted: Mon May 15, 2006 5:04 pm Post subject: |
|
|
Centurion
Joined: 19 Apr 2006
Posts: 144
|
But in my case, since I have broker and config manager installed on the same machine, I use the same ID to start both of them. I am not sure if this is causing the problem.
I checked the event log,it too says the same thing as the BIP error codes I mentioned in my previous post. |
|
| Back to top |
|
|
| madi |
| Posted: Mon May 15, 2006 6:54 pm Post subject: |
|
|
Chevalier
Joined: 17 Jan 2006
Posts: 475
|
i got this error some time ago but the flow did get deployed, did you check that??
also the problem went away on its own 
--madi |
|
| Back to top |
|
|
|
|
|
| |
|
Page 1 of 1 |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
