| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
  |
|
| Configuring WMQI Brokers |
« View previous topic :: View next topic » |
| Author |
Message
|
| prasannal |
 Posted: Thu Nov 13, 2003 8:54 am Post subject: Configuring WMQI Brokers |
 |
|
Apprentice
Joined: 04 Aug 2003
Posts: 44
|
Hi,
If I want a broker with their a queue managers and Configuration manager using another queue manager.
Then, What is essential to set communication between Config. Qmgr and Broker Queue Manager.
Pls let me know. |
|
| Back to top |
|
 |
| emiranda |
| Posted: Thu Nov 13, 2003 9:02 am Post subject: |
|
|
Disciple
Joined: 21 Nov 2002
Posts: 196
Location: Dublin, Ireland
|
Just the sender and receiver channels and the xmitq  .
_________________
Warm Regards,
EM |
|
| Back to top |
|
|
| jefflowrey |
| Posted: Thu Nov 13, 2003 9:47 am Post subject: |
|
|
Grand Poobah
Joined: 16 Oct 2002
Posts: 19981
|
Yes, as emiranda says.
This is documented in the Installation and Planning guide. You should read through it.
_________________
I am *not* the model of the modern major general. |
|
| Back to top |
|
|
| vmn |
| Posted: Thu Nov 13, 2003 9:18 pm Post subject: |
|
|
Novice
Joined: 10 Nov 2003
Posts: 16
Location: Helsinki, Finland
|
Hi,
what version are you using? I tried the same with WBIMB 5.0 CSD02 as per Websphere MQ Integrator V2.1 Admin Guide, Managing the Configuration Manager. I set up channels,ports, listeners, xmitqs. I also verified that channels were up and running.
I could not get it working. The configmgr never found the two brokers I had. I reverted back to single qm, multiple execution groups. May it's a bug.
Regards,
Veli-Matti |
|
| Back to top |
|
|
| jefflowrey |
| Posted: Fri Nov 14, 2003 5:26 am Post subject: |
|
|
Grand Poobah
Joined: 16 Oct 2002
Posts: 19981
|
| vmn wrote: |
Hi,
what version are you using? I tried the same with WBIMB 5.0 CSD02 as per Websphere MQ Integrator V2.1 Admin Guide, Managing the Configuration Manager. I set up channels,ports, listeners, xmitqs. I also verified that channels were up and running.
I could not get it working. The configmgr never found the two brokers I had. I reverted back to single qm, multiple execution groups. May it's a bug.
Regards,
Veli-Matti |
The ConfigMgr in WBIMB is *much* different than it is in 2.1. It's a lot simpler, for one.
You should easily be able to register multiple brokers with the v5 ConfigMgr. But you probably have to follow the appropriate instructions for v5, rather than the instructions for v2.1.
_________________
I am *not* the model of the modern major general. |
|
| Back to top |
|
|
| vmn |
| Posted: Sun Nov 16, 2003 9:43 pm Post subject: |
|
|
Novice
Joined: 10 Nov 2003
Posts: 16
Location: Helsinki, Finland
|
|
| Back to top |
|
|
|
|
|
| |
|
Page 1 of 1 |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
