| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
  |
|
| Cluster configuration + mqipt |
« View previous topic :: View next topic » |
| Author |
Message
|
| rmcervantes |
 Posted: Wed Jan 30, 2013 10:23 am Post subject: Cluster configuration + mqipt |
 |
|
Newbie
Joined: 30 Jan 2013
Posts: 2
|
Hi,
i'm trying to establish a cluster communication through mqipt using socks, but there's problems with auto-defined cluster channel, everytime i create a cluster sender channels, the other queue manager creates an auto-defined cluster sender channel trying to connect directly to the queuemanager skipping the mqipt.
SVR1(QM1 -> MQIPT(socks client)) -> SVRIPT(MQIPT(socks server)) -> SVR2(QM2)
and
SVR2(QM2 -> MQIPT(socks client)) -> SVRIPT(MQIPT(socks server)) -> SVR1(QM1)
Have anyone used this type of configuration?  |
|
| Back to top |
|
 |
| exerk |
| Posted: Wed Jan 30, 2013 11:28 am Post subject: |
|
|
Jedi Council
Joined: 02 Nov 2006
Posts: 6339
|
To be honest, I cannot think of any reason to put MQIPT between clustered queue managers; what is your rationale for using this configuration?
_________________
It's puzzling, I don't think I've ever seen anything quite like this before...and it's hard to soar like an eagle when you're surrounded by turkeys. |
|
| Back to top |
|
|
| fjb_saper |
| Posted: Wed Jan 30, 2013 11:29 am Post subject: |
|
|
Grand High Poobah
Joined: 18 Nov 2003
Posts: 20756
Location: LI,NY
|
You need to create a cluster receiver with the mqipt address and port in it. 
_________________
MQ & Broker admin |
|
| Back to top |
|
|
| mqjeff |
| Posted: Wed Jan 30, 2013 1:17 pm Post subject: |
|
|
Grand Master
Joined: 25 Jun 2008
Posts: 17447
|
| exerk wrote: |
| To be honest, I cannot think of any reason to put MQIPT between clustered queue managers; what is your rationale for using this configuration? |
Right, to be clear here.
Every queue manager in the cluster must be able to connect to every other queue manager in the cluster.
So in order to do this, you must establish an mqipt endpoint for every other queue manager in the cluster, and you must then create a cluster receiver channel for every queue manager in the cluster with the mqipt address for that cluster queue manager.
And then all cluster communications go through mqipt, and no cluster communications go any other way.
The only way this makes some small sense is if you have a small cluster with two queue managers on each side of MQIPT, such that you have redundant and load-balanced connections across a hard network boundary. But to do this, you then need to make sure that you have an entirely separate cluster for the rest of the mq network on each side of the mqipt boundary. And you're still vulnerable to poor object definitions causing cluster bleedthrough and allowing messages to pass from one cluster to another, if you're not diligent in applying management, governance and security.
It is probably simpler to use mqipt features to create load balanced destinations with a virtual single external end point. |
|
| Back to top |
|
|
| rmcervantes |
| Posted: Thu Feb 28, 2013 4:03 pm Post subject: |
|
|
Newbie
Joined: 30 Jan 2013
Posts: 2
|
Thanks everybody. Sorry, i was very busy to Reply.
Finnally, i put the ip address and port of the MQIPT to the other cluster-receiver channel and it works, but addtionally found a problem with other queue manager in the cluster on the same lan, because this one does not go through MQIPT.
SVRA(QMA) <-> SVRB(QMB -> MQIPT(socks client)) -> SVRIPT(MQIPT(socks server)) -> SVRC(QMC)
On this configuration QMA and QMB are over cluster but QMB and QMC too.
I found a different configuration of Cluster-Receiver CONNAME parameter using more than one ip and port, like CONNAME('1.1.1.1(1234),9.9.9.9(4321)') giving this configuration to the cluster-sender channel and if 1.1.1.1(1234) is not available, it tries with 9.9.9.9(4321), excelent option i think...
Thanks again.  |
|
| Back to top |
|
|
|
|
|
| |
|
Page 1 of 1 |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
