| Not able to deploy .bar/message flow with message set in MB7 |
| Not able to deploy .bar/message flow with message set in MB7 |
|
100% |
[ 1 ] |
| MB7 deployment exception |
|
0% |
[ 0 ] |
| MB7 deployment exception |
|
0% |
[ 0 ] |
|
| Total Votes : 1 |
|
| Author |
Message
|
| satchin |
 Posted: Wed Feb 09, 2011 2:48 pm Post subject: Not able to deploy .bar/message flow with message set in MB7 |
 |
|
Apprentice
Joined: 08 Feb 2011
Posts: 33
|
Hi All,
I am new to MBv7. I have deployed normal message flows. But I am not able to deploy message flow with message set. When I created bar file with these 2 I am getting the same problem. I have downloaded sample applications from IBM portal which has message set then also facing the same problem.
Below is the exceptioin I am getting, pls provide me solution for this.
Many thanks in advance. |
|
| Back to top |
|
 |
| Vitor |
| Posted: Wed Feb 09, 2011 3:04 pm Post subject: Re: Not able to deploy .bar/message flow with message set in |
|
|
Grand High Poobah
Joined: 11 Nov 2005
Posts: 26093
Location: Texas, USA
|
| satchin wrote: |
| Below is the exceptioin I am getting, pls provide me solution for this. |
What exception?
And what's with the poll?
_________________
Honesty is the best policy.
Insanity is the best defence. |
|
| Back to top |
|
|
| satchin |
| Posted: Wed Feb 09, 2011 4:10 pm Post subject: Re: Not able to deploy .bar/message flow with message set in |
|
|
Apprentice
Joined: 08 Feb 2011
Posts: 33
|
| Quote: |
The entire internal configuration message failed to be processed successfully.
Use the messages following this message to determine the reasons for the failure. If the problem cannot be resolved after reviewing these messages, contact your IBM Support center. Enabling service trace may help determine the cause of the failure.BIP4041E: Execution group 'CHANGENAMESPACE' received an invalid configuration message. See the following messages for details of the error.
The broker was asked to deploy a message flow which contained properties that were not recognized by the broker. This typically results from a message flow requiring a version or type of node that is not supported by the broker installation. |
|
|
| Back to top |
|
|
| Vitor |
| Posted: Thu Feb 10, 2011 5:02 am Post subject: Re: Not able to deploy .bar/message flow with message set in |
|
|
Grand High Poobah
Joined: 11 Nov 2005
Posts: 26093
Location: Texas, USA
|
| satchin wrote: |
| The broker was asked to deploy a message flow which contained properties that were not recognized by the broker. This typically results from a message flow requiring a version or type of node that is not supported by the broker installation. |
That seems clear enough.
_________________
Honesty is the best policy.
Insanity is the best defence. |
|
| Back to top |
|
|
| mqjeff |
| Posted: Thu Feb 10, 2011 6:13 am Post subject: |
|
|
Grand Master
Joined: 25 Jun 2008
Posts: 17447
|
| So did you use Toolkit 7.0 to build a bar file that you tried to deploy to a 6.1 Broker? |
|
| Back to top |
|
|
| satchin |
| Posted: Thu Feb 10, 2011 4:24 pm Post subject: |
|
|
Apprentice
Joined: 08 Feb 2011
Posts: 33
|
| mqjeff wrote: |
| So did you use Toolkit 7.0 to build a bar file that you tried to deploy to a 6.1 Broker? |
I have created the bar file in Toolkit 7.0 and trying to deploy in Broker 7.0 only. |
|
| Back to top |
|
|
|
|
