| Author |
Message
|
| chris boehnke |
 Posted: Wed Nov 28, 2007 11:12 am Post subject: SOAPEnvelope and SOAPExtract nodes in MB |
 |
|
Partisan
Joined: 25 Jul 2006
Posts: 369
|
Hi Guys,
I am on MB 6.0 fixpak 2
My broker is on Unix box and toolkit on Windows.
I upgraded my toolkit. I dont see the SOAPEnvelope and SOAPExtract nodes in my toolkit. Cant we get these nodes just by upgrading the toolkit???.
Suggestions please..
Thanks. |
|
| Back to top |
|
 |
| sknrt1 |
| Posted: Wed Nov 28, 2007 11:29 am Post subject: |
|
|
Apprentice
Joined: 22 Jan 2003
Posts: 39
Location: USA
|
Nope, it comes in a support pac - ia9o
Here is the link:
http://www-1.ibm.com/support/docview.wss?uid=swg24014070
Also you need to have a Broker runtime at 6.0.0.3 or above.
_________________
------------------------------------------
sk
MQ User since 2001
Message Broker User since 2001
IBM Certified
Solution Designer - WebSphere MQ
Solution Developer - Message Broker |
|
| Back to top |
|
|
| TonyD |
| Posted: Wed Nov 28, 2007 11:32 am Post subject: |
|
|
Knight
Joined: 15 May 2001
Posts: 540
Location: New Zealand
|
| Not sure what you mean by ' ...upgrading the Toolkit'. You need to follow the instructions in the Installation Guide that describe installation using RUP. Is this what you did? The nodes will then appear in the 'Web Services' drawer of the Palette. |
|
| Back to top |
|
|
| chris boehnke |
| Posted: Wed Nov 28, 2007 11:42 am Post subject: |
|
|
Partisan
Joined: 25 Jul 2006
Posts: 369
|
| TonyD wrote: |
| Not sure what you mean by ' ...upgrading the Toolkit'. You need to follow the instructions in the Installation Guide that describe installation using RUP. Is this what you did? The nodes will then appear in the 'Web Services' drawer of the Palette. |
Hi Tony,
I mean:
In the MB Toolkit, going to the Help tab->Software Updates->IBM Rational Product Updater |
|
| Back to top |
|
|
| TonyD |
| Posted: Wed Nov 28, 2007 12:08 pm Post subject: |
|
|
Knight
Joined: 15 May 2001
Posts: 540
Location: New Zealand
|
Chris,
I sent my reply before sknrt1's reply arrived ... as he (she?) says, the SOAP nodes are installed separately from a supportpac. You must download it and then use RUP, as described in Section 5.2 of the Installation Guide, to install the SOAP nodes as an 'optiomal feature'. |
|
| Back to top |
|
|
| Bill.Matthews |
| Posted: Wed Nov 28, 2007 12:13 pm Post subject: |
|
|
Master
Joined: 23 Sep 2003
Posts: 232
Location: IBM (Retired)
|
It is better to go ahead and shutdown the toolkit and run RUP from the Start list since you will be asked to shutdown the toolkit in any case.
Note that the use of RUP goes away with V6.1 (and any RAD V7 based tooling) - there the Toolkit updates are handled by the Installation Manager.
I wexpect the same requirement will exist - shutdown the toolkit first. Its rather difficult to replace code while it is in use.
While on the V6.1 subject - these nodes are built in. When using the new SOAPInput node you can still use the SOAPExtract node. However, the SOAPReply is a bit smarter (since only SOAP msgs are allowed) and it can add the SOAP Envelope automatically, should you not have a reason to build it yourself.
_________________
Bill Matthews |
|
| Back to top |
|
|
|
|
