| Author |
Message
|
| elvis_gn |
 Posted: Thu Jun 15, 2006 11:17 pm Post subject: |
 |
|
Padawan
Joined: 08 Oct 2004
Posts: 1905
Location: Dubai
|
Hi chaitrali,
Have u started all the serives...including the QMs and DB.
Are u able to disconnect and connect successfully in the toolkit ?
There would have been 2-3 errors in the event viewer...check those too...even the event log.
Regards. |
|
| Back to top |
|
 |
| elvis_gn |
| Posted: Thu Jun 15, 2006 11:29 pm Post subject: |
|
|
Padawan
Joined: 08 Oct 2004
Posts: 1905
Location: Dubai
|
Hi chaitrali,
So ur deploying a bar file to the Execution group right ? Open the bar file and check all your files with some XML validator....most probably one of the names u have used does not conform to standards...
Are u getting any errors in the flow or the message sets...see if errors are listed in the Problems pane in the toolkit...are all the files getting added successfully to the bar file ?
Regards. |
|
| Back to top |
|
|
| PieterV |
| Posted: Thu Jun 15, 2006 11:58 pm Post subject: |
|
|
Disciple
Joined: 04 Jan 2006
Posts: 164
Location: Belgium
|
Did you had any problems with that execution group?
Did you deleted that execution group and recreated it? |
|
| Back to top |
|
|
| elvis_gn |
| Posted: Fri Jun 16, 2006 1:17 am Post subject: Re: Error while deploying flow |
|
|
Padawan
Joined: 08 Oct 2004
Posts: 1905
Location: Dubai
|
Hi chaitrali,
| chaitrali wrote: |
| The problem is not only while deploying but when i try to remove the existing message flow (after stopping it) it doesnt give any error nor does it remove the message flow |
So u tried to delete a flow first and then add a new one...the last one could not be deleted...
Restarting the ConfigMgr and Broker should fix this...
If it dosen't you could delete the execution group and create it again...but that comes later...
Regards. |
|
| Back to top |
|
|
| Mensch |
| Posted: Fri Jun 16, 2006 3:23 am Post subject: |
|
|
Disciple
Joined: 17 Jul 2005
Posts: 166
|
Hi
What error you are getting while removing message folw?
you can try out following :
remove old bar file
create new bar file and add msg flows/msg set
and then redeploy.
_________________
Thanks and Regards ,
Mensch |
|
| Back to top |
|
|
| PieterV |
| Posted: Fri Jun 16, 2006 3:53 am Post subject: |
|
|
Disciple
Joined: 04 Jan 2006
Posts: 164
Location: Belgium
|
| please tell us how you have solved the problem |
|
| Back to top |
|
|
| fjb_saper |
| Posted: Sat Jun 17, 2006 4:00 pm Post subject: |
|
|
Grand High Poobah
Joined: 18 Nov 2003
Posts: 20756
Location: LI,NY
|
I've seen this happen in V6. Usually all you need to do is disconnect and reconnect the config mgr. This may happen if during connection of the config mgr (the toolkit subscribes to the brokers' deployment messages) some subscription was not successful.
Enjoy 
_________________
MQ & Broker admin |
|
| Back to top |
|
|
| PieterV |
| Posted: Mon Oct 02, 2006 12:54 am Post subject: |
|
|
Disciple
Joined: 04 Jan 2006
Posts: 164
Location: Belgium
|
I have the same problem: i can see the subsciptions and i get BIP1536S when deploying;
- reconnecting doesnt work,
- restarting doesnt work,
I have another similar configuration on the same system (with the same problem): Configuration Manager + Broker.
When i deleted both CM and Broker and recreated them the problem was solved.
Altough i don't find this a clean solution,
is there anything else i can do? |
|
| Back to top |
|
|
| mqmatt |
| Posted: Tue Oct 03, 2006 4:14 am Post subject: |
|
|
Grand Master
Joined: 04 Aug 2004
Posts: 1213
Location: Hursley, UK
|
| Try using the CMP API Exerciser - right click on the broker and select 'Resubscribe to status topics'. |
|
| Back to top |
|
|
| PieterV |
| Posted: Tue Oct 03, 2006 9:56 pm Post subject: |
|
|
Disciple
Joined: 04 Jan 2006
Posts: 164
Location: Belgium
|
I tried that already,
it has no effect.
We also have the rights to see the subscriptions. |
|
| Back to top |
|
|
|
|
