| Author |
Message
|
| Sriver |
 Posted: Fri Jun 09, 2006 1:48 am Post subject: Unsubscribe objects in Flow Manager |
 |
|
Newbie
Joined: 08 Jun 2006
Posts: 6
|
Hi,
I had a problem with one collaboration. The reason was that the messages were not pass through so they just got into the SAP Adapter AP Queue I am using.
In order to be able to have all those error messages in the Flow Manager to be able to reprocess then in a control way, I did change the collab set up to Defered.
The thing is that now I have all of those messages in the Flow Manager, but due to a can not restart the adapter yet they are with the follow error status: "Cannot Find subscribtion for business object......" .
Is this a problem, or once the adapter is up and runnign the data will go with no problems?
On the other hand, I have other 100 messages stuck in the Unsibscribed queue.
How could I handle this ones?
Thanks a lot for your help. |
|
| Back to top |
|
 |
| Kram |
| Posted: Fri Jun 09, 2006 6:06 am Post subject: |
|
|
Voyager
Joined: 02 Mar 2006
Posts: 87
|
if you are not able to start the adapter ... check what the problem is ...
"Cannot Find subscribtion for business object"......check if the connector configuration supports the Business objects used in the collaboration
_________________
Regards,
Ram |
|
| Back to top |
|
|
| Sriver |
| Posted: Fri Jun 09, 2006 6:16 am Post subject: |
|
|
Newbie
Joined: 08 Jun 2006
Posts: 6
|
This object is being used for a long time ago already, so yep, 100% sure that is supported.
So I don't understand the reason for the issue.
Could be the fact that adapter is down for a while due to conectivity problems?
Regards. |
|
| Back to top |
|
|
| Kram |
| Posted: Fri Jun 09, 2006 6:19 am Post subject: |
|
|
Voyager
Joined: 02 Mar 2006
Posts: 87
|
when u try starting the adapter whats happening? can you post any logs?
_________________
Regards,
Ram |
|
| Back to top |
|
|
| Sriver |
| Posted: Fri Jun 09, 2006 6:24 am Post subject: |
|
|
Newbie
Joined: 08 Jun 2006
Posts: 6
|
[Time: 2006/06/09 13:14:53.745] [System: ConnectorAgent] [SS: UL_FEU_ECLIPSE_MQSeriesConnector] [Thread: main (#1888161947)] [Mesg: [Type: Info] [MsgID: 17021] [Mesg: No response from connector controller. It is probably not running yet. Reason: UL_FEU_ECLIPSE_MQSeriesConnector. Retrying...] ]
So restarting the controller the adapter goes up, but there are still messages in the unsubscribed queue. How could I handled those?
Thanks in advance.
Regards |
|
| Back to top |
|
|
| Kram |
| Posted: Fri Jun 09, 2006 6:56 am Post subject: |
|
|
Voyager
Joined: 02 Mar 2006
Posts: 87
|
if messages are in unsubscribed queue it means the connector config needs to be validated.. else see if you can resend those messages from source application.
_________________
Regards,
Ram |
|
| Back to top |
|
|
| Sriver |
| Posted: Fri Jun 09, 2006 7:00 am Post subject: |
|
|
Newbie
Joined: 08 Jun 2006
Posts: 6
|
I think that this would need further investigation, cos the adapter config is the right one.
On the other hand, your suggestion about resubmiting from the source system is the one I used to use, but the problem is when selecting the data to be resubmited from the queue. Using rfhutil, CommerQuest or MQExplorer u only can access one to one to the messages, so having 100 or even more is quite slow.
Thanks a lot for ur help anyway.
Kind Regards. |
|
| Back to top |
|
|
|
|
