| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
  |
|
| Clustered Queue not Visible |
« View previous topic :: View next topic » |
| Author |
Message
|
| Robert123 |
 Posted: Fri Mar 24, 2006 12:30 am Post subject: Clustered Queue not Visible |
 |
|
Newbie
Joined: 23 Mar 2006
Posts: 4
|
Hi,
I am using MQ 6.0 and have got two of my queue manager QMgr1 and QMgr2 into the cluster "Clster". I create a Queue "Test" under QMgr1 and in the properties of the queue make it as a shared queue under the cluster.
I do not see the Queue "Test" under QMgr2 in the MQExplorer but i see that both the QMgr1 and QMgr2 under the cluster. What could be the problem?
When i try to put a message from the command prompt, i am able to post the message to the Queue "Test" using either of the Queue managers, but when i try to read the message, it gives me the 2085 exception if i read it from the QMgr2 but get the message if i read it from QMgr1. Why is this so?
-Robert |
|
| Back to top |
|
 |
| wschutz |
| Posted: Fri Mar 24, 2006 2:59 am Post subject: |
|
|
Jedi Knight
Joined: 02 Jun 2005
Posts: 3316
Location: IBM (retired)
|
Robert -- what are you seeing is normal custering behavior. When you define a queue to a cluster, you can PUT to that queue from any other qmgr in the cluster, but you can only GET from it on those qmgrs where you defined it as a QLOCAL.
_________________
-wayne |
|
| Back to top |
|
|
| vennela |
| Posted: Sat Mar 25, 2006 12:41 am Post subject: |
|
|
Jedi Knight
Joined: 11 Aug 2002
Posts: 4055
Location: Hyderabad, India
|
| Quote: |
| I do not see the Queue "Test" under QMgr2 in the MQExplorer but i see that both the QMgr1 and QMgr2 under the cluster. What could be the problem? |
Can't you see the queue on QMGR2 even after you put a message using QMGR2? |
|
| Back to top |
|
|
| Robert123 |
| Posted: Sun Mar 26, 2006 8:51 pm Post subject: |
|
|
Newbie
Joined: 23 Mar 2006
Posts: 4
|
| vennela wrote: |
| Quote: |
| I do not see the Queue "Test" under QMgr2 in the MQExplorer but i see that both the QMgr1 and QMgr2 under the cluster. What could be the problem? |
Can't you see the queue on QMGR2 even after you put a message using QMGR2? |
No I don't see the Queue even after i post the message. But in case of MQ 5.3, i could see the clustered queue under all the queue managers that are there in the cluster. Can't the same thing been seen in MQ 6.0 |
|
| Back to top |
|
|
| vennela |
| Posted: Wed Mar 29, 2006 2:14 pm Post subject: |
|
|
Jedi Knight
Joined: 11 Aug 2002
Posts: 4055
Location: Hyderabad, India
|
Can you see the queue using mqsc commands
|
|
| Back to top |
|
|
|
|
|
| |
|
Page 1 of 1 |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
