| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
  |
|
| WBIMB V5.0 not supported with WMQ 6.0 |
« View previous topic :: View next topic » |
| Author |
Message
|
| rb462627 |
 Posted: Thu Jul 21, 2005 4:29 am Post subject: WBIMB V5.0 not supported with WMQ 6.0 |
 |
|
Novice
Joined: 23 Apr 2004
Posts: 23
Location: Hartford, CT
|
While attempting to install WMQ V6 on my laptop, was prompted to install Eclipse 3.0.1 as a prereq.
This concerned me as I need to continue to support my production applications via WBIMB Toolkit which runs Eclipse 2.0.3.
When I brought this up to IBM their response was as follows:
"To answer your question WBIMB V5.0 toolkit is not compatible with Eclipse 3.0.1. As you mentioned in the pmr the 5.0 toolkit uses Eclipse 2.0.3. These two versions of Eclipse are not compatible. This is partially the reason WBIMB V5.0 is not supported with WMQ 6.0. Our next release of WBIMB slated for the end of this year (assuming all goes as planned) should be compatible with Eclipse 3.0.1 and WMQ 6.0"
Is anyone else out there running WMQ V6 with WBIMB V5 toolkit?
If so, are you experiencing any problems?
Thanks
_________________
Ralph Beckers
IBM Certified Specialist - MQSeries
IBM Global Services - The Hartford Account
Office #: 860.547.4745
ralph.beckers@thehartford.com
rbeckers@us.ibm.com
"No! Try Not. Do. Or Do Not... There Is No Try!" Master Yoda |
|
| Back to top |
|
 |
| jefflowrey |
| Posted: Thu Jul 21, 2005 4:35 am Post subject: |
|
|
Grand Poobah
Joined: 16 Oct 2002
Posts: 19981
|
Yes, this works just fine.
No, this will not overwrite the Eclipse for Toolkit if you install this.
The v6 MQ Explorer is a set of Eclipse plug-ins that are only compatible with Eclipse 3.01 or later. You can run a separate installer for the Eclipse SDK from within the WebSphere MQ installer, and by default it will install into a different location than your WBIMB toolkit.
But you will need to run a separate Eclipse window to use MQ Explorer, and can't integrate the plug-ins into the WBIMB Toolkit. It is the same with WSAD.
And Broker runs, but perhaps is not supported, on MQv6.
_________________
I am *not* the model of the modern major general. |
|
| Back to top |
|
|
| rb462627 |
| Posted: Thu Jul 21, 2005 4:42 am Post subject: WBIMB V5.0 not supported with WMQ 6.0 |
|
|
Novice
Joined: 23 Apr 2004
Posts: 23
Location: Hartford, CT
|
Thanks Jeff
Guess I'll give it a shot then....
Regards
_________________
Ralph Beckers
IBM Certified Specialist - MQSeries
IBM Global Services - The Hartford Account
Office #: 860.547.4745
ralph.beckers@thehartford.com
rbeckers@us.ibm.com
"No! Try Not. Do. Or Do Not... There Is No Try!" Master Yoda |
|
| Back to top |
|
|
|
|
|
| |
|
Page 1 of 1 |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
