| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
  |
|
| Attaching to Flow Engine stops Agent Controller |
« View previous topic :: View next topic » |
| Author |
Message
|
| subhacom |
 Posted: Fri Jan 07, 2005 5:28 am Post subject: Attaching to Flow Engine stops Agent Controller |
 |
|
Newbie
Joined: 07 Jan 2005
Posts: 3
Location: India
|
Hi,
I have WBIMB v 5.0.0 with CSD04 and RAC5.0.2 on WinXP. When trying to attach to any dataflow engine in localhost the following error message appears:
| Quote: |
RAServer.exe - Application Error
The instruction at "0x003511d0" referenced memory at "0x00000000". The memory could not be "read". |
The service "IBM Agent Controller" stops after this. No Flow Engine appears in "Select the Flow Engine" dialogue when I try to do the same after starting Agent Controller service again.
No error message appears in <AgentControllerInstallDir>\config\servicelog.log
Another point is that I installed only CSD04 and none of the earlier fixpacks as I was not sure if they are incremental or independent of each other.
Could somebody help?
Thanks in advance.
subhacom |
|
| Back to top |
|
 |
| kirani |
| Posted: Sat Jan 08, 2005 6:04 pm Post subject: |
|
|
Jedi Knight
Joined: 05 Sep 2001
Posts: 3779
Location: Torrance, CA, USA
|
Please post WMQI related questions into WMQI Forum.
_________________
Kiran
IBM Cert. Solution Designer & System Administrator - WBIMB V5
IBM Cert. Solutions Expert - WMQI
IBM Cert. Specialist - WMQI, MQSeries
IBM Cert. Developer - MQSeries
|
|
| Back to top |
|
|
| kirani |
| Posted: Sat Jan 08, 2005 6:26 pm Post subject: |
|
|
Jedi Knight
Joined: 05 Sep 2001
Posts: 3779
Location: Torrance, CA, USA
|
Take a look at this thread,
http://www.mqseries.net/phpBB2/viewtopic.php?t=19754
Try to refresh the IBM RAC from CSD4 link.
_________________
Kiran
IBM Cert. Solution Designer & System Administrator - WBIMB V5
IBM Cert. Solutions Expert - WMQI
IBM Cert. Specialist - WMQI, MQSeries
IBM Cert. Developer - MQSeries
|
|
| Back to top |
|
|
| subhacom |
| Posted: Mon Jan 10, 2005 3:56 am Post subject: Still having problem |
|
|
Newbie
Joined: 07 Jan 2005
Posts: 3
Location: India
|
Hi,
My apologies for the mistake I made (being a newbie in this field).
And regarding agent controller, I have installed the latest RAC release from IBM site.
The windows error message I mentioned was resolved by removing the .metadata folder in eclipse workspace directory of WBIMB after installing CSD04.
But even after that as I attach to a data flow engine, the flow debug view does not show any message flow under the flow-engine entry. But it does not give any error message either.
And although I put break points to all outgoing connections from MQInput node in the message flow editor, the messages pass to proper queue without being caught in the debugger.
Thanks and regards.
subhacom |
|
| Back to top |
|
|
|
|
|
| |
|
Page 1 of 1 |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
