| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
  |
|
| IIB9: Selectively encrypting / decrypting elements in XML |
« View previous topic :: View next topic » |
| Author |
Message
|
| akil |
 Posted: Wed Oct 08, 2014 10:07 pm Post subject: IIB9: Selectively encrypting / decrypting elements in XML |
 |
|
Partisan
Joined: 27 May 2014
Posts: 338
Location: Mumbai
|
Hi
I have a use-case in which an XML like the following needs to be created. There are 2 elements, of which the second one is Mpin, this is an RSA encrypted value. To do this, I can write a JCN but is there a better (in built way?).
1. Can the certificates in the broker KeyStore be accessed programmatically in a JCN to avoid managing the certificates separately?
2. Is there any other way to do this without writing a JCN?
This is not a SOAP message , this is an XML payload sent over HTTPS.
| Quote: |
<Params>
<Param>
<ParamId>4</ParamId>
<ParamName>MainMenu</ParamName>
<ParamValue>8</ParamValue>
<ParamType>String</ParamType>
</Param>
<Param>
<ParamId>5</ParamId>
<ParamName>Mpin</ParamName>
<ParamValue>
7JlEfu1pmqkrAqjjDBC9XaqL4JJ7l9%2fxM4qxgp2CpnNJXT2lKlrHdFGLQCiFX3t6%2fNmriZp1H5fJmCP21H3fL2FlmVfdpQ2cuEV%2fhvSToDPDPvTqmx9Pbfs
bLACeqRiOG5BwgFxZ5a3vXVpqUhIakbTqO8ftO3nqXF2zL%2b5K%2b94nVwBtWtHOpDz6B%2fVycy988SsTfp7tVDOugweaf5spsqDZJezklVe2nRYL2BYesJ
ZTWekcwSRArUJGOkavWMYwYjNHol5FJUTaucrLcbLMhQkDYcpVdywe2fMLmvKMQyTX74mRXFboqBP9gXA9GDIO8LvSwMWEXN9JrH9uzjWKSg%3d%3d
</ParamValue>
<ParamType>String</ParamType>
</Param>
</Param>
|
[/list]
_________________
Regards |
|
| Back to top |
|
 |
| akil |
| Posted: Sat Oct 18, 2014 3:45 am Post subject: |
|
|
Partisan
Joined: 27 May 2014
Posts: 338
Location: Mumbai
|
Hi
So I gave this a shot with custom code in JCN, I am now at a stage where I need to read the private key from the brokers keystore to decrypt the incoming field. I can access the location of the brokers key store using the CMP , but I am unable to figure out how do I open the keystore and get hold of the key as both have passwords.
Any suggestions on how I can proceed with using the standard broker keystore, instead of doing file operations in my JCN ?
Regards
Akhilesh
_________________
Regards |
|
| Back to top |
|
|
| fjb_saper |
| Posted: Sat Oct 18, 2014 5:51 am Post subject: |
|
|
Grand High Poobah
Joined: 18 Nov 2003
Posts: 20696
Location: LI,NY
|
| akil wrote: |
Hi
So I gave this a shot with custom code in JCN, I am now at a stage where I need to read the private key from the brokers keystore to decrypt the incoming field. I can access the location of the brokers key store using the CMP , but I am unable to figure out how do I open the keystore and get hold of the key as both have passwords.
Any suggestions on how I can proceed with using the standard broker keystore, instead of doing file operations in my JCN ?
Regards
Akhilesh |
Have you thought about setting up a SOAP service passing it the XML? Could you then use wss to decrypt it?
Have fun 
_________________
MQ & Broker admin |
|
| Back to top |
|
|
| akil |
| Posted: Sat Oct 18, 2014 8:07 am Post subject: |
|
|
Partisan
Joined: 27 May 2014
Posts: 338
Location: Mumbai
|
Hi
Do you mean a flow like as follows
Flow 1 (that will send the encrypted element mPIN):
HTTPInput --> SoapRequest
Flow 2 (created to decrypt the element)
SoapInput --> ...
I thought about it, but wasn't too sure if something that's usually, done. I can try it for sure, I prefer using built in nodes as much as possible..but some specs like these are dictated by folks who don't really care much about standard..
I also went through the CMP documents & the Plugin JavaDoc, but did not find any information that could tell me if I could just get the loaded private keys..
Regards
Akhilesh
_________________
Regards |
|
| Back to top |
|
|
|
|
|
| |
|
Page 1 of 1 |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
