| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
| Websphere MQ 5.3.. channel in retrying mode... |
« View previous topic :: View next topic » |
| Author |
Message
|
| cactus |
 Posted: Thu Oct 17, 2002 10:02 am Post subject: |
 |
|
Apprentice
Joined: 12 Oct 2002
Posts: 30
|
IP address is correct as i double checked .............. still 
regards
cactus |
|
| Back to top |
|
 |
| Tibor |
| Posted: Thu Oct 17, 2002 2:18 pm Post subject: |
|
|
Grand Master
Joined: 20 May 2001
Posts: 1033
Location: Hungary
|
| dgolding wrote: |
I don't think CCSID comes into it all at this stage - we're just trying to get the connection up, sending a message comes later!  |
Don,
That was only an idea, because I had a lot of problems with differently localized MQ servers and clients. Moreover, CCSID problem used to be reported only one side, another MQ sends only TCPIP errors to the log file...
BUT this seems something else.
cactus,
Are you running your listener process from MMC or command prompt? I recommend you starting the listener as a command line process as Don mentioned. Possibly you can get a lot of extra info in this way.
Additionally, take a look of sockets with "netstat -an | find 1415"
Tibor |
|
| Back to top |
|
|
| cactus |
| Posted: Thu Oct 17, 2002 5:12 pm Post subject: |
|
|
Apprentice
Joined: 12 Oct 2002
Posts: 30
|
Hi,
runmqlsr -t tcp -p 1415 -m QM2 ,ran this command there was error saying that AMQ9218......becoz QM2 is running on same port...so ,i have changed the sender channel port number to 1416.
runmqlsr -t tcp -p 1416 -m QM2.Its not giving any error but still when trying to start sender channel, It is going to retry mode.
checked the status of the port with commnad
netstat -a
all the listeners were running...
anything else...
thanks
cactus |
|
| Back to top |
|
|
| dgolding |
| Posted: Thu Oct 17, 2002 8:40 pm Post subject: |
|
|
Yatiri
Joined: 16 May 2001
Posts: 668
Location: Switzerland
|
...I'm running out of ideas here....
As Tibor and Brandon mentioned, you have to be ABSOLUTELY sure about your port number allocation. Try using TELNET to your machine, and override the port number by using 1416. You should manage to get connected, and then when type some stuff it will disconnect you.
If this doesn't work, and you can't connect, your LAN setup needs looking at.
You have got QM2 running, haven't you?  |
|
| Back to top |
|
|
| cactus |
| Posted: Thu Oct 17, 2002 10:50 pm Post subject: |
|
|
Apprentice
Joined: 12 Oct 2002
Posts: 30
|
Yeah me too.......
QM2 very much running........Its TCP/IP error......(10038) X2736..I don't know how to resove this issue.......
thanks
Cactus |
|
| Back to top |
|
|
| dgolding |
| Posted: Thu Oct 17, 2002 10:55 pm Post subject: |
|
|
Yatiri
Joined: 16 May 2001
Posts: 668
Location: Switzerland
|
| Did you try the telnet on port 1416? If that's not working (if the runmqlsr program is running on port 1416) then you have a network, not an MQ problem.... |
|
| Back to top |
|
|
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
