| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
  |
|
| Disconnect a broker and connect it to a different CM |
« View previous topic :: View next topic » |
| Author |
Message
|
| Yanghui |
 Posted: Tue Jan 28, 2003 10:33 am Post subject: Disconnect a broker and connect it to a different CM |
 |
|
Disciple
Joined: 08 May 2002
Posts: 151
Location: Dublin, Ireland
|
Hi,
Does anybody know if it's possible to disconnect a broker from its CM and connect it to a different CM with all msgflow and msgset retained?
I tried to delete broker's reference in CM and then delete a physical broker. After that, I recreated it by using old db and qm but I found actually all the message sets and message flows have been removed after I configure another CM to pick it.
I am thinking maybe it's not doable. Any information about this would be highly appreciated. Many thanks in advance.
Regards
-Yanghui |
|
| Back to top |
|
 |
| kirani |
| Posted: Tue Jan 28, 2003 1:44 pm Post subject: |
|
|
Jedi Knight
Joined: 05 Sep 2001
Posts: 3779
Location: Torrance, CA, USA
|
Well, the configuration manager database contains your message flows, message sets are stored into MRM database. If you are planning to migrate existing data (Msg flow and msg set) to the new Config mgr then make a copy of existing CM and MRM Db and use these db when creating new configuration manager.
_________________
Kiran
IBM Cert. Solution Designer & System Administrator - WBIMB V5
IBM Cert. Solutions Expert - WMQI
IBM Cert. Specialist - WMQI, MQSeries
IBM Cert. Developer - MQSeries
|
|
| Back to top |
|
|
| Yanghui |
| Posted: Thu Jan 30, 2003 12:56 am Post subject: |
|
|
Disciple
Joined: 08 May 2002
Posts: 151
Location: Dublin, Ireland
|
Thank you, Kirani,
I won't create a new CM but let another existing CM manage a broker which has been managed by its previous CM. Also I can't make a copy of existing CM and MRM db since its db2 software is corrupted, which is the reason why I need to do this.
If this can't be done, it would mean that if CM is gone, we have no way to get any information out from all its runtime environments (brokers).
Any comments or ideas are appreciated. Thanks.
-Yanghui |
|
| Back to top |
|
|
| kirani |
| Posted: Thu Jan 30, 2003 8:02 pm Post subject: |
|
|
Jedi Knight
Joined: 05 Sep 2001
Posts: 3779
Location: Torrance, CA, USA
|
Yanghui,
If you are saying that the old configuration manager and MRM database is corroupted and you don't have the exported message flows/sets or a backed-up copy of these databases then I don't think there is a way to get source code (Message flows and message set).
Without your old configuration manager you can still use the boker but you will not be able to deploy (or change) anything to this broker.
I guess you will have to first delete the existing broker, which was connected to the old config mgr and then recreate the broker with same broker database, then add this Broker to existing (new) CM.
In a development environment It's always good to export your message flows/sets on daily basis.
_________________
Kiran
IBM Cert. Solution Designer & System Administrator - WBIMB V5
IBM Cert. Solutions Expert - WMQI
IBM Cert. Specialist - WMQI, MQSeries
IBM Cert. Developer - MQSeries
|
|
| Back to top |
|
|
|
|
|
| |
|
Page 1 of 1 |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
