ASG
IBM
Zystems
Cressida
Icon
Netflexity
 
  MQSeries.net
Search  Search       Tech Exchange      Education      Certifications      Library      Info Center      SupportPacs      LinkedIn  Search  Search                                                                   FAQ  FAQ   Usergroups  Usergroups
 
Register  ::  Log in Log in to check your private messages
 
RSS Feed - WebSphere MQ Support RSS Feed - Message Broker Support

MQSeries.net Forum Index » WebSphere Message Broker (ACE) Support » only one in terminal??

Post new topic  Reply to topic
 only one in terminal?? « View previous topic :: View next topic » 
Author Message
suneelsh
PostPosted: Thu Apr 18, 2002 12:40 am    Post subject: Reply with quote

Acolyte

Joined: 13 Apr 2002
Posts: 69
Location: Pune,India

I wanted to write a plugin node that takes 2 xml sources and gives back one xml in the o/p. But the smartguide only gives option to create only one i/p terminal. I need 2! how do i go about this??

[ This Message was edited by: suneelsh on 2002-04-18 01:41 ]
Back to top
View user's profile Send private message Send e-mail
devans
PostPosted: Thu Apr 18, 2002 1:23 am    Post subject: Reply with quote

Apprentice

Joined: 18 Mar 2002
Posts: 43

You can have multiple input terminals set up in your plugin code, but
the plug-in SmartGuide only allows you to specify one input terminal.
Take a look at Appendix D of the WMQI Programming Guide. That will tell you how to hand craft the files which are normally created by the SmartGuide. In these files, you can define your two input terminals.
Back to top
View user's profile Send private message
suneelsh
PostPosted: Thu Apr 18, 2002 3:39 am    Post subject: Reply with quote

Acolyte

Joined: 13 Apr 2002
Posts: 69
Location: Pune,India

devans I have proceeded as the manual and I need only 2 files: the xml file and the wdp file right?? or do i have to create the additional property files??

I stopped the contol center service &put these two files in the messageprocessingnode dir & started it again. and when i choose it from the msg flow and add it to the control center and right click it...I get only remove option. There are no check in,check out options. Where did i go wrong?
Back to top
View user's profile Send private message Send e-mail
kirani
PostPosted: Thu Apr 18, 2002 10:35 am    Post subject: Reply with quote

Jedi Knight

Joined: 05 Sep 2001
Posts: 3779
Location: Torrance, CA, USA

Probably you have not placed your files in correct directory. the files should be placed in following directory.
<wmqi_root>Toolrepositoryprivate<hostname or IP Address>MessageProcessingNode


_________________
Kiran


IBM Cert. Solution Designer & System Administrator - WBIMB V5
IBM Cert. Solutions Expert - WMQI
IBM Cert. Specialist - WMQI, MQSeries
IBM Cert. Developer - MQSeries

Back to top
View user's profile Send private message Visit poster's website
suneelsh
PostPosted: Thu Apr 18, 2002 10:47 pm    Post subject: Reply with quote

Acolyte

Joined: 13 Apr 2002
Posts: 69
Location: Pune,India

no i have placed the files in the correct dir. When i right click to check in i get only remove.
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic  Reply to topic Page 1 of 1

MQSeries.net Forum Index » WebSphere Message Broker (ACE) Support » only one in terminal??
Jump to:  



You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
Protected by Anti-Spam ACP
 
 


Theme by Dustin Baccetti
Powered by phpBB © 2001, 2002 phpBB Group

Copyright © MQSeries.net. All rights reserved.