| |
|
RSS Feed - WebSphere MQ Support
|
RSS Feed - Message Broker Support
|
 |
|
| Configuring questions.. |
« View previous topic :: View next topic » |
| Author |
Message
|
| jnsunkersett |
 Posted: Fri May 07, 2004 1:22 pm Post subject: Configuring questions.. |
 |
|
Newbie
Joined: 07 May 2004
Posts: 3
|
Hi,
I am new to MQ visual edit.
Using ver 1.2.0
Following the included tutorial, I created a "Queue Manager Access" profile.
I gues I can use any name. Need not hv any relation to queue names or...
In that I cud not figure out what "Queue manager Name" to give. 
I am using WSAD5 as my development env with "Embedded messaging" as my JMS Server. I do not have WebsphereMQ installed on my box.
So pls cud you tell me what I shud specify for QueueManager
In my Websphere Test Env configuration I specificied :
QueueConnectionFactory, WASQueueEntries, Queues and ListenerPorts.
thks
g1 |
|
| Back to top |
|
 |
| RogerLacroix |
| Posted: Fri May 07, 2004 10:13 pm Post subject: |
|
|
Jedi Knight
Joined: 15 May 2001
Posts: 3253
Location: London, ON Canada
|
Hi,
I have not used the embedded messaging with WAS but you must have given the queue manager a name.
Look in the JNDI tree for the QCF (QueueConnectionFactory) that you are using and what is the value of the 'Queue Manager' attribute in the QCF?
Hope that helps.
Regards,
Roger Lacroix
_________________
Capitalware: Transforming tomorrow into today.
Connected to MQ!
Twitter |
|
| Back to top |
|
|
| jnsunkersett |
| Posted: Mon May 10, 2004 4:58 am Post subject: |
|
|
Newbie
Joined: 07 May 2004
Posts: 3
|
Hi,
The QCF (QueueConnectionFactory) does not seem to have an attribute for 'Queue Manager'.
I have uploaded the image to
http://photos.yahoo.com/jnsunkersett, in the 'Forums' album, there is only 1 jpg
PS:
[img]http://f1.pg.photos.yahoo.com/ph/jnsunkersett/detail?.dir=/e917&.dnm=4adc.jpg[/img] |
|
| Back to top |
|
|
| RogerLacroix |
| Posted: Mon May 10, 2004 7:50 am Post subject: |
|
|
Jedi Knight
Joined: 15 May 2001
Posts: 3253
Location: London, ON Canada
|
Hi,
For your 'OfflineQCF' (I think that is the name - it's hard to read), open up the properties window and look for either 'QMGR' or 'Queue Manager Name'. But I don't what you will find because you are using 'javax.jms.QueueConnectionFactory'. Note: MQ Visual Edit is not designed to work with native JMS.
If you use 'com.ibm.mq.jms.MQQueueConnectionFactory' for your QCF then I know for sure that you will find the correct information.
Regards,
Roger Lacroix
Capitalware Inc.
_________________
Capitalware: Transforming tomorrow into today.
Connected to MQ!
Twitter |
|
| Back to top |
|
|
| jnsunkersett |
| Posted: Mon May 10, 2004 8:18 am Post subject: |
|
|
Newbie
Joined: 07 May 2004
Posts: 3
|
Got it configured!
FYI. This is how I did it.
Start the server (or local WebSphere test environ)
In a command prompt go to the \bin folder of MQ install directory.
Execute the command: dspmq
This will show you the name for your queue manager. e.g. WAS_localhost_server1
Then execute: runmqsc <<specify-name-of-the-QM-found above>>
and then execute display qlocal ('*') - this will give u the queue names
With this information
Fill in the dialog boxes of MQVisual Edit as appropriate.
PS: Keep the "Remote Parameters" block QM profile blank - do not choose 'Set default'
thks
G1 |
|
| Back to top |
|
|
| RogerLacroix |
| Posted: Mon May 10, 2004 8:39 am Post subject: |
|
|
Jedi Knight
Joined: 15 May 2001
Posts: 3253
Location: London, ON Canada
|
Hi,
Actually, I did not know that the embedded version included the dspmq command. That definitely makes life easier.
Also, you do not need to get a list of queues from outside of MQ Visual Edit because once you have the queue manager configured, all you need to do is click the List button on the Open Queue window to get the list of queues.
Lastly, I will give a little clarification on the Remote Paramters. WMQ supports 2 ways for a client application to connect to a queue manager: client and binding mode. -When your application is running on the same box as the queue manager, then you can use binding mode. The WMQ API calls will use JNI and be much, much faster.
-When your application is NOT running on the same box as the queue manager (i.e. different box) then you MUST code hostname/IP, Port number and Channel Name for your application to successfully connect to the queue manager. This is called client mode.
In your case, you are running the application (i.e. MQ Visual Edit) on the same box as where the queue manager is running. Therefore, you ONLY need to specify the queue manager name in the MQ Visual Edit's 'Queue Manager Access Profile' window.
In the future, if you wish to have MQ Visual Edit connect to a remote queue manager, then you will need to fill in the Remote Parameters on the 'Queue Manager Access Profile' window.
Regards,
Roger Lacroix
Capitalware Inc. |
|
| Back to top |
|
|
|
|
|
| |
|
Page 1 of 1 |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
|
|
|
