ASG
IBM
Zystems
Cressida
Icon
Netflexity
 
  MQSeries.net
Search  Search       Tech Exchange      Education      Certifications      Library      Info Center      SupportPacs      LinkedIn  Search  Search                                                                   FAQ  FAQ   Usergroups  Usergroups
 
Register  ::  Log in Log in to check your private messages
 
RSS Feed - WebSphere MQ Support RSS Feed - Message Broker Support

MQSeries.net Forum Index » WebSphere Message Broker (ACE) Support » Segmentation fault: mqsicreatebroker (WMQI2.1, AIX)

Post new topic  Reply to topic
 Segmentation fault: mqsicreatebroker (WMQI2.1, AIX) « View previous topic :: View next topic » 
Author Message
gteplits
PostPosted: Fri Jan 18, 2002 8:18 am    Post subject: Reply with quote

Apprentice

Joined: 16 Jul 2001
Posts: 29

Environment:
AIX 4.3.3; UDB DB2 7.2 ; WMQI2.1

Command mqsicreatebroker MQSI20_BROKER -i user -a password -q QM1 -n DBNAME
abends with "Segmentation fault".
The same AIX machine hosted MQSI2.0.1 broker before, but was upgraded to WMQI2.1
Before upgrade broker was deleted using mqsideletebroker command.
No relevant trace information is written to the system log.

Any suggestions/pointers are greatly appreciated.

George
Back to top
View user's profile Send private message
kirani
PostPosted: Fri Jan 18, 2002 10:50 am    Post subject: Reply with quote

Jedi Knight

Joined: 05 Sep 2001
Posts: 3779
Location: Torrance, CA, USA

Have you tried recreating your broker database?

Kiran
Back to top
View user's profile Send private message Visit poster's website
jantonitis
PostPosted: Sun Jan 20, 2002 12:03 pm    Post subject: Reply with quote

Newbie

Joined: 27 Jun 2001
Posts: 7
Location: Jason Antonitis

I posted this same reply to the MQSeries Listserv.

Check your .odbc.ini definitions. If you are using DB2 v7.2 Fix Pak 2 or later you need to use the db2_36.o library. Most likely you are currently using db2.o. This is detailed in the DB2 Fix Pak release notes. Also, the sample odbc definitions can be found in the WMQI Administration manual,Chapter 3 (page 35).

Jason Antonitis
ajason@us.ibm.com
EAI National Practice
Back to top
View user's profile Send private message Send e-mail
gteplits
PostPosted: Mon Jan 21, 2002 7:50 am    Post subject: Reply with quote

Apprentice

Joined: 16 Jul 2001
Posts: 29

Jason:

Once again, many thanks for your response. Pointing to correct odbc file has rectified the problem.
Back to top
View user's profile Send private message
jantonitis
PostPosted: Tue Jan 22, 2002 9:37 am    Post subject: Reply with quote

Newbie

Joined: 27 Jun 2001
Posts: 7
Location: Jason Antonitis

The reply I posted earlier will work in most circumstances but is not officially supported by IBM. Changing the .odbc.ini settings as directed above could cause problems with XA transactions. Information on this problem can be found at:

http://www-3.ibm.com/software/ts/mqseries/platforms/supported/wsmq_integ_for_aix_2_1.html

Contact your local IBM Support Representative for more details.
Back to top
View user's profile Send private message Send e-mail
Display posts from previous:   
Post new topic  Reply to topic Page 1 of 1

MQSeries.net Forum Index » WebSphere Message Broker (ACE) Support » Segmentation fault: mqsicreatebroker (WMQI2.1, AIX)
Jump to:  



You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
Protected by Anti-Spam ACP
 
 


Theme by Dustin Baccetti
Powered by phpBB © 2001, 2002 phpBB Group

Copyright © MQSeries.net. All rights reserved.