ASG
IBM
Zystems
Cressida
Icon
Netflexity
 
  MQSeries.net
Search  Search       Tech Exchange      Education      Certifications      Library      Info Center      SupportPacs      LinkedIn  Search  Search                                                                   FAQ  FAQ   Usergroups  Usergroups
 
Register  ::  Log in Log in to check your private messages
 
RSS Feed - WebSphere MQ Support RSS Feed - Message Broker Support

MQSeries.net Forum Index » WebSphere Message Broker (ACE) Support » How to open a bar file in a graphic design mode in Toolkit?

Post new topic  Reply to topic
 How to open a bar file in a graphic design mode in Toolkit? « View previous topic :: View next topic » 
Author Message
EricL
PostPosted: Fri Mar 16, 2018 12:13 pm    Post subject: How to open a bar file in a graphic design mode in Toolkit? Reply with quote

Centurion

Joined: 10 Oct 2014
Posts: 100

Hi

I have a bunch of bar files, I can see these bar files have been deployed into different broker nodes, I'd like take a close look at all the nodes inside each bar file so that I can customize them when necessary, my question is how can I open these bar files in "Integration Tool Kit" in graphic mode so that I can see each node and connections between them?

Thanks in advance !
Eric
Back to top
View user's profile Send private message
fjb_saper
PostPosted: Fri Mar 16, 2018 11:17 pm    Post subject: Re: How to open a bar file in a graphic design mode in Toolk Reply with quote

Grand High Poobah

Joined: 18 Nov 2003
Posts: 20696
Location: LI,NY

EricL wrote:
Hi

I have a bunch of bar files, I can see these bar files have been deployed into different broker nodes, I'd like take a close look at all the nodes inside each bar file so that I can customize them when necessary, my question is how can I open these bar files in "Integration Tool Kit" in graphic mode so that I can see each node and connections between them?

Thanks in advance !
Eric

The exercise is futile. You should go back to the source code. It will have all that you need.
You did put it into a source control system right?
_________________
MQ & Broker admin
Back to top
View user's profile Send private message Send e-mail
Vitor
PostPosted: Mon Mar 19, 2018 4:58 am    Post subject: Re: How to open a bar file in a graphic design mode in Toolk Reply with quote

Grand High Poobah

Joined: 11 Nov 2005
Posts: 26093
Location: Texas, USA

EricL wrote:
my question is how can I open these bar files in "Integration Tool Kit" in graphic mode so that I can see each node and connections between them?


The same way you examine the ingredients used in a cake once it's been baked, iced and served.

Seriously.

You find out how the cake was made by asking for the original recipe; in this case the recipe is the copy of the source in the source repository my worthy associate refers to.

And before you say anything along the lines of, "that's a ridiculous limitation of the product", think how much luck you'd have performing this exercise on an exe file.
_________________
Honesty is the best policy.
Insanity is the best defence.
Back to top
View user's profile Send private message
Display posts from previous:   
Post new topic  Reply to topic Page 1 of 1

MQSeries.net Forum Index » WebSphere Message Broker (ACE) Support » How to open a bar file in a graphic design mode in Toolkit?
Jump to:  



You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
Protected by Anti-Spam ACP
 
 


Theme by Dustin Baccetti
Powered by phpBB © 2001, 2002 phpBB Group

Copyright © MQSeries.net. All rights reserved.